MINI R56 Fuel Injector Replacement – 2006-2013 Cooper – N12 (Non-Turbo)

0
285

MINI R56 Fuel Injector Replacement – 3 Hours

repair models
MakeModelSubmodelEngineYearChasis
MINICooperBaseN12 (non-turbo)AllR56
MINICooperBaseN12 (non-turbo)AllR57
difficulty bar
The Repair Difficulty Level displays graphically how challenging the repair is, from easy to advanced. Easy repairs usually require very few tools, have short repair times and do not require jacking and supporting the vehicle. As the difficulty level rises, expect the repair to demand more time, specialized tools, and better understanding of mechanics to complete the job.

The BMW Repair Guide used this 2007 MINI Cooper for the following article. To see other repairs on our site using this actual car, please click on the image below!

Repair Summary
The following article gives detailed instructions on replacing the fuel injectors in a Generation 2 MINI R56 car. Even though we have used a 2006 MINI Cooper to perform this installation, this article can be applied to any 2006-2013 Cooper (non-turbo) vehicle with minor modifications.

A MINI R56 fuel injector replacement is a very straightforward procedure for the home mechanic that can save an expensive trip to the local repair shop.

It is well known that the N12 engines found in the second generation MINI Cooper have issues. Fortunately the majority of these problems can be avoided by following a strict maintenance schedule. Changing out the fuel injectors in your MINI Cooper is a good example of a repair that should be done long before you start encountering misfiring cylinders and “check engine” lights on the dashboard.

The fuel injectors in your MINI N12 four cylinder engine are simple solenoid valves that pump a fine mist of pressurized fuel into the cylinder. Over time these valves can become clogged from fuel hydrocarbons and additives, restricting their flow and severely affecting engine performance. Signs of dirty fuel injectors are rough idling, difficult engine starting, failed emissions, misfiring cylinders, smoke emanating from the tailpipe and over all poor engine performance.

Even though there isn’t a suggested maintenance interval for fuel injectors in the MINI Cooper Service and Warranty Information guide, the BMW Repair Guide recommends that they are replaced every 100,000 miles to avoid any of the engine issues listed above.

A MINI R56 fuel injector replacement is actually a relatively simple procedure that can be easily done by any capable home mechanic. It does not require putting the MINI in its “service position”; the fuel rail and injectors can be easily accessed from the engine compartment.

Affiliate link disclosure – The BMW Repair Guide uses affiliate links in their site. For more information on affiliate links, please click here.

1. Fuel injectors (required) Always use a high quality fuel injector from an OEM manufacturer. NEVER use cheap “aftermarket” injectors…they may seem like a good deal at the time, but they have a high failure rate and can actually damage your engine. We give you a couple of great choices based on your budget.

Fuel injector – Genuine MINI 13537528176

MINI R56 Cooper (does not fit Cooper S or JCW models).

Fuel injector – VDO 13537528176

MINI R56 Cooper (does not fit Cooper S or JCW models).

2. Spark plugs (optional) Compliment your new fuel injectors with a fresh set of spark plugs. Please see our article MINI R56 Tune Up for more in formation on replacing them.

Spark plugs – Bosch ZQR8SI302

MINI R56 Cooper (non-turbo)

3. Air filter (optional) Now is a great time to change out your air filter. Compliment your new fuel injectors by helping your MINI engine breath easier with a fresh filter.

Air filter 61235 – Mann 13717561235

MINI R56 Cooper and Cooper S

10mm socket wrench
T25 torx bit
T30 torx bit
Torque wrench- low range
Metal pick
Screwdriver – flat blade

Section 1 – MINI R56 fuel injector removal
Removing the fuel injectors from your MINI R56 Cooper is a simple procedure. It is very important to ALWAYS remove the negative terminal from the battery before starting this repair. Not disconnecting the battery can cause damage to sensitive engine electronics.

  1. Locate the battery on the right side of the vehicle in the back of the engine compartment.MINI R56 Fuel Injector Replacement - locate battery under hoodBattery compartment
  2. Use a 10mm socket wrench to remove the negative terminal cable. If your negative terminal cable has an intelligent battery sensor attached to it, be very careful not to bump or drop it. For more information what the battery sensor looks like and how it functions, please see our article BMW E60 Battery Sensor Failure/Repair – 2004-2010 5 Series – All Models.MINI R56 Fuel Injector Replacement - remove negative terminal lead
  3. Locate the fuel injectors…they are located at the back of the valve cover on the fuel rail, underneath the intake muffler that houses the air filter.MINI R56 fuel injectors - Locate the engine fuel injectors located on fuel rail behind valve cover.
  4. In order to get to the injectors, some parts need to be cleared out of the way. Start by pinching in the plastic tabs and removing the intake manifold tube from the intake manifold pre-box.MINI R56 fuel injectors - Remove the intake manifold tube from the pre-box. Pull the intake manifold tube free from the pre-box.
  5. Using a 10mm socket wrench, remove the bolt anchoring the intake manifold pre-box to the engine. Grasp the pre-box and pull free from the intake muffler.MINI R56 fuel injectors - Unbolt the intake manifold pre-box from the engine. MINI R56 fuel injectors - Remove the pre-box from the engine compartment.
  6. Disconnect the mass air flow (MAF) sensor. This connection can be a little tricky…the release is under the plug. Try using a metal pick to depress the release then pull the plug free.MINI R56 fuel injectors - Unclip the MAF sensor connection. Its a little tricky...use a metal pick to release it if necessary. Pull the MAF connector free from the sensor.
  7. Use a 10mm socket wrench to loosen the bolt anchoring the intake muffler to the engine.MINI R56 fuel injectors - Loosen the intake muffler anchor bolt.
  8. Loosen the hose clamp connecting the intake muffler to the rubber boot.Loosen the hose clamp connecting the rubber boot to the intake muffler.
  9. Use a T25 torx bit to loosen the four intake muffler lid screws. Remove the lid off of the intake muffler.MINI R56 fuel injectors - Use a torx bit to loosen the intake muffler lid screws.MINI R56 fuel injectors - Remove the lid from the intake muffler.
  10. Grasp the base of the intake muffler and pull it loose from the body of the car. It is held in place by two rubber grommets.MINI R56 fuel injectors - Remove the intake muffler base from the vehicle.
  11. You can now see the fuel rail on the back of the engine. The fuel injectors are attached to the bottom of the rail.MINI R56 fuel injectors - Locate the fuel rail on the back of the engine.
  12. Before disconnecting the fuel rail, it is good practice to release any fuel pressure that might be left in the system. This is done by simply depressing the Schrader valve located on the end of the rail. First, locate the Schrader valve and remove its protective cap.
  13. Lay a rag under the Schrader valve to catch any fuel that may be ejected when releasing the pressure. Press the valve stem in with a small screwdriver or metal pick to release the pressure in the fuel rail (it’s like releasing the pressure from a tire valve). Replace the cap when you are finished.MINI R56 fuel injectors - Release the pressure in the fuel rail by depressing the Schrader valve
  14. Remove the fuel line from the end of the fuel rail by retracting the black lock ring and pulling it free as shown below. Have a rag ready to catch any fuel that may spill out.MINI R56 fuel injectors - Retract the black collar to release the fuel line from the fuel rail. Pull the fuel line off of the fuel rail.
  15. The next step requires removing the two T30 bolts anchoring the fuel rail to the cylinder head. The two bolts are difficult to see since they are behind the engine…use an inspection mirror to locate them if necessary.MINI R56 fuel injectors - Remove the two torx bolts anchoring the fuel rail to the engine. Fuel rail torx screw
  16. When you have removed the two T30 mounting bolts, grasp the fuel rail with both hands and pull the injectors free from the cylinder head. You may have to gently rock it back and forth while pulling to get the injectors to release.MINI R56 fuel injectors - Pull the fuel injectors from the cylinder head.
  17. Unclip the wiring harness from the back of the valve cover. Unclip the injector wiring harness from the back of the valve cover. MINI R56 fuel injectors - Pull the fuel rail out away from the engine so the electrical connections can be removed.
  18. Remove the injector electrical connector by pressing down on the upper tab and pulling it off. Be sure to use some tape to label the wires to avoid reinstalling them in the incorrect order.MINI R56 fuel injectors - Release the injector's electrical connection by depressing the plastic tab MINI R56 fuel injectors - Pull the connection free from the injector. MINI R56 fuel injectors - Label the connections so you don't mix them up when reinstalling.
  19. Use a metal pick or small flat blade screwdriver to pry the injector clamp free from the fuel rail. Pull the injectors out of the rail.MINI R56 fuel injectors - Pry the injector clamp loose from the fuel rail MINI R56 fuel injectors - Pull the injector out of the fuel rail A MINI R56 fuel injector.
  20. Using both hands, firmly press the new injectors into the fuel rail until they click into place. MINI R56 fuel injectors - Use both hands to install the new fuel injectors.
  21. Reattach all of the electrical connectors to the fuel injectors paying close attention to the correct numbering order. Push them firmly on the injectors until you hear them click.MINI R56 fuel injectors - Reinstall the electrical connections. Make sure to hear them "click" into place.
  22. If you used tape to label the connections, remove it now.
  23. The next step can be tricky, so use patience. Install the fuel injectors into the cylinders. It helps to tilt the fuel rail forward to get them in. If you are having a problem getting the injectors in, try wiggling the fuel rail back and forth. DO NOT put pressure on the fuel rail until you are certain the injectors are in the cylinders. DO NOT try and force the injectors into the cylinder…you will damage them. Make sure the injectors are properly line up with the holes in the cylinder head. MINI R56 fuel injectors - Tilt the fuel rail forward if you are having problems getting the injectors in.
  24. When all four injectors are properly in the cylinders, use the palm of your hand to firmly press down on the fuel rail. Continue to press firmly on each injector until their o-ring is properly seated inside the cylinder. MINI R56 fuel injectors - Use the palm of your hand to seat the injectors in the cylinders.
  25. Reinstall the two T30 fuel rail mounting bolts and torque to 8 Nm (6 ft-lb).MINI R56 fuel injectors - Reinstall the fuel rail mounting bolts and torque to 8 Nm (6 ft-lb).
  26. Reinstall the fuel line on the end of the fuel rail. Make sure to press firmly on the fitting until you hear it snap into place.
  27. Reinstall the intake muffler. Now is a great time to install a new air filter…you can order one from the parts list above. Don’t forget to plug the MAF connection back in.
  28. Reinstall the pre-box and intake manifold tube.
  29. Reconnect the battery.
  30. Start the car and test for proper operation.

 

MINI R56 Fuel Injector Replacement Finished
If you have any questions or comments, please feel free to contact us. And congratulations for Doing It Yourself!