MINI R56 Thermostat Replacement – 2006-2013 Cooper – All Models

0
134

MINI R56 thermostat replacement – 3 hours

Repair cost 2

The BMW Repair Guide used this 2007 MINI Cooper for the following article. To see other repairs on our site using this actual car, please click on the image below!

Repair Summary
The following article gives detailed instructions on replacing the thermostat on a MINI R56 Cooper car. Even though we have used a 2007 MINI Cooper to perform this repair, this article can be applied to any 2006-2013 (second generation) MINI R56/57 vehicle with minor modifications.

A cracked MINI R56 thermostat is a common source of coolant leaks in Cooper and Cooper S vehicles.

The thermostat on the MINI R56 is located on the left side of the engine, below the main wiring harness. It is composed of a one piece plastic “housing” with a built in thermostat that regulates the amount of coolant being sent to the engine.

The thermostat is simply a mechanical valve that opens and closes depending on the temperature of the engine. When the engine is cold the thermostat remains closed, blocking coolant from circulating through the engine block. As the motor slowly heats up, the thermostat opens allowing fluid to travel in which prevents the engine from overheating. The BMW R56 thermostat allows the engine to warm up correctly and prevents premature wear of critical parts in your vehicle’s power plant. If coolant was allowed to flow through a cold engine, the motor would struggle to reach operating temperature and would run very rough until it warmed up.

The MINI R56 thermostat housing is a very common source of engine coolant leaks due to its plastic construction and its close proximity to the exhaust manifold inside the engine compartment. The brutal heat generated by the MINI R56 exhaust manifold takes its toll on the thermostat’s plastic housing causing it to crack. Coolant will begin to seep out of these fractures, pooling on top of the transmission and ultimately finding its way to the garage floor. Signs of a leaking MINI R56 thermostat may also include a white residue around the thermostat housing area and low reservoir coolant level that constantly needs replenishment.

Coolant from a leaking MINI R56 thermostat
A classic sign of a leaking thermostat in a MINI Cooper…coolant on top of the transmission case.

The interior mechanical thermostat can also fail causing it to stick in the open or closed position. A thermostat that has become stuck in the open position will allow coolant to enter a cold engine, causing a rough idle and poor performance until the motor heats up. A thermostat stuck in the closed position is an extremely serious situation since coolant cannot enter a hot engine, causing overheating and possible engine failure. Please be aware there are also many other parts that can fail in the MINI R56 that can cause engine overheating (including the coolant temperature sensor), so a full diagnoses of the coolant system should always be done before attributing it to the the thermostat.

A MINI R56 thermostat replacement is a relatively straightforward procedure that does not require the engine compartment to be put in the service position. It does require that the engine’s wiring harness be partially disconnected, so be sure to always disconnect the battery before starting this repair. Not disconnecting the battery prior to starting this repair can cause serious damage to sensitive electronics.

Affiliate link disclosure – The BMW Repair Guide uses affiliate links in their site. For more information on affiliate links, please click here.

1. Thermostat assembly (required) – All MINI thermostat assemblies come with the housing, thermostat, sensor, clip and gaskets. Always use a high quality replacement part…cheap aftermarket thermostats have short lifespans and a high failure rate. We give you two great options based on your budget and brand preference.

Thermostat housing – ECS Tuning 11537534521KT5KT

Fits all MINI R56/57 models - 06/2010 through 03/2012 require adapter lead (see description)

Thermostat housing – Genuine MINI 11538699290

Fits all MINI R56/57 models - 06/2010 through 03/2012 require adapter lead (see description)

2. Thermostat sensor adapter lead (may be required) – The plug on the temperature sensor wire was changed in all MINI models produced from 05/2010 through 03/2012. If you have a MINI produced during this time period, you will need to purchase this adapter lead for the sensor plug to fit the new replacement thermostat.

Thermostat sensor adapter lead – HT 12517646145

Fits all MINI R56/57 models with a production date of 06/2010 through 03/2012.

3. Engine coolant (required) – Since you will lose some of the engine coolant when you remove the thermostat, you will need to have some on hand to replace it. The BMW Repair Guide only recommends using Genuine MINI (BMW) anitfreeze/coolant in your vehicle. Please remember that Genuine MINI/BMW coolant comes concentrated…it must be mixed 50/50 with distilled water from your local grocery store.

Coolant/Anti-freeze – Genuine BMW 82141467704

T30 torx bit
8mm hex socket
10mm socket wrench
Torque wrench- low range
Metal pick
Screwdriver – flat blade
CRC Brākleen

Section 1- Preparing for removing the MINI R56 thermostat
The MINI R56 thermostat is located on the left side of the engine, directly underneath the main wiring harness. In order to gain clear access to the thermostat, the wiring harness must be partially disconnected and folded back out of the way. The MINI does not need to be put in its “service position” to remove the thermostat…it can be easily accessed from the top of the engine compartment.

  1. Before starting the MINI R56 thermostat replacement, you must disconnect the negative terminal from the battery. Since the main wiring harness will need to be disconnected from multiple sensors as well as the DME (engine control module), failure to disconnect the battery could cause catastrophic damage to sensitive electronics.
  2. Using a 10mm socket wrench, remove the negative terminal from the battery and wrap it in a rag to avoid it from inadvertently touching the terminal.MINI R56 battery compartmentMINI R56 thermostat replacement - remove negative terminal lead
  3. In order to get to the MINI R56 thermostat, some parts need to be cleared out of the way. Start by pinching in the plastic tabs and removing the intake manifold tube from the intake manifold pre-box.MINI R56 thermostat replacement - Remove the intake manifold tube from the pre-box.MINI R56 thermostat replacement - Pull the intake manifold tube free from the pre-box.
  4. Using a 10mm socket wrench, remove the bolt anchoring the intake manifold pre-box to the engine. Grasp the pre-box and pull free from the intake muffler.MINI R56 thermostat replacement - Unbolt the intake manifold pre-box from the engine. MINI R56 thermostat replacement - Remove the pre-box from the engine compartment.
  5. It is very difficult to remove the intake manifold tube from the front bumper. We strongly suggest just bungee cording it out of the way instead of attempting to remove it.
  6. Next, the engine wiring harness will need to be cleared out so the thermostat can be accessed. Start by disconnecting the intake and exhaust camshaft sensors on the left side of the valve cover. MINI R56 thermostat replacement - Disconnect the intake camshaft sensor MINI R56 thermostat replacement - Disconnect the exhaust camshaft sensor
  7. We highly recommend marking all of your connections with high visibility tape to aid during reassembly.Mrk all connections with high visibility tape
  8. Remove the vacuum hose from the vacuum pump by squeezing its connection and pulling it free.MINI R56 thermostat replacement - Remove the vacuum hose from the vacuum pump
  9. With the aid of a flat blade screwdriver, remove the protective cover off of the DME control box.Remove the cover off of the DME box MINI R56 thermostat replacement - Remove the DME box cover
  10. Remove the first two plugs from the DME by depressing the plastic lock tabs and pulling up the releases.MINI R56 thermostat replacement - Unlock the first harness connector by pressing the release tab MINI R56 thermostat replacement - Remove the first connector from the DME MINI R56 thermostat replacement - Remove the second connector from the DME
  11. Pull the wiring harness’ plastic anchor free from the DME bracket.MINI R56 thermostat replacement - Remove plastic wiring harness anchor
  12. Disconnect the lower lead on the wiring harness.Disconnect the lower lead on the wiring harness
  13. Next, grab the wiring harness and pull it up and off of the thermostat. The wiring harness has two plastic tabs on the bottom that fit into two holes in the plastic thermostat housing.Wiring harness plastic mounting tabs Thermostat mounting holes for wiring harness.
  14. Disconnect the oil pressure switch from the right side of the engine.MINI R56 thermostat replacement - Remove the oil pressure sensor
  15. Disconnect the coolant temperature sensor from the top of the thermostat.MINI R56 thermostat replacement - Remove the coolant temperature sensor
  16. Disconnect the essentric shaft position sensor by grasping its connector and pulling straight up.MINI R56 thermostat replacement - Remove the essentric shaft position sensor
  17. Moving back to the front of the engine, remove the two engine cover screws with a T30 torx bit. Remove the engine cover from the valve cover.Remove the two T30 engine cover screws MINI R56 thermostat replacement - Remove the engine cover from the car
  18. Disconnect the four ignition coils by lifting their retaining brackets and pulling the sockets free. MINI R56 thermostat replacement - Release the coil socketMINI R56 thermostat replacement - remove the plug from the ignition coil
  19. Disconnect the front exhaust VANOS solenoid by lifting the plastic locking tab and pulling the connection apart.MINI R56 thermostat replacement - Disconnect the exhaust VANOS solenoid.
  20. Remove the harness grounding wire with an 8mm socket wrench.MINI R56 thermostat replacement - remove ground wire
  21. Unsnap the wiring harness from the front of the valve cover.
    MINI R56 thermostat replacement - remove wiring harness
  22. Fold the wiring harness back towards the rear of the engine compartment and disconnect the thermostat sensor. The sensor is a little tricky to release…try using a metal pick to reach under the connection and pull the locking clip down.Remove the thermostat sensor from back of thermostat cover. Pull the locking tab down to release the sensor plug.MINI R56 thermostat replacement - Disconnect the thermostat sensor.
  23. The wiring harness is now free. Gently fold it back and stow it out of the way. You now have clear access to remove the thermostat.MINI R56 thermostat replacement - fold the wiring harness back to rear of engine compartment You now have clear access to remove the thermostat.

 

Section 2 – Removing the MINI R56 thermostat
Removing the thermostat requires disconnecting the coolant lines and unbolting it from the side of the engine block. The step that gives many mechanics trouble is removing the thermostat from the rear water supply tube. Use patience and care when disconnecting the water supply tube…breaking it will require having to remove the water pump to install a new one.

  1. Position a drain pan under the thermostat to catch any coolant that drains out of the engine.
  2. Using a flat blade screwdriver, remove the upper radiator hose from the thermostat.MINI R56 thermostat replacement - Remove the upper radiator hose from thermostat
  3. Remove the lower radiator supply hose from the thermostat.MINI R56 thermostat replacement - Remove the lowerr radiator hose from thermostat
  4. Remove the expansion tank coolant hose from the front of the thermostat. Remove the expansion tank coolant hose from the front of the thermostat.
  5. Moving to the rear of the thermostat, remove the two heater supply and return hoses. Make sure not to mix them up, they both run to the heater core and can easily be installed incorrectly during reassembly. We like to mark ours with tape just to be sure. MINI R56 thermostat replacement - Remove the rear heater hoses. MINI R56 thermostat replacement - Remove the rear heater hoses.
  6. Finally, the rear water supply pipe needs to be released from the thermostat. The rear water supply pipe runs from the water pump on the right side of the engine to the back of the thermostat. Using a metal pick (or your fingers), pull the metal locking clip up to release the pipe. AVOID pulling the clip off of the pipe…if you do it can be a pain getting it back on.Release the metal locking clip on the rear water supply tube.
  7. The thermostat can now be unbolted from the engine and removed from the vehicle. Use a 10mm socket wrench to remove the three thermostat mounting bolts. We suggest using an extension and low profile socket to reach the rear mounting bolt.MINI R56 thermostat replacement - Remove the thermostat mounting boltsMINI R56 thermostat replacement - Remove the thermostat mounting bolts
  8. Grasp the thermostat with both hands and remove from the engine. The thermostat can be very difficult to release from the rear water supply pipe. Try gently rocking back and forth while pulling until it releases.MINI R56 thermostat replacement - Rock the thermostat back and forth while pulling Thermostat removed from the engine block
  9.  Liberally soak a clean rag in CRC Brakleen and thoroughly clean the engine block where the thermostat mounts. Make sure to remove any grease or old rubber that may have been left from the thermostat gasket. CRC BrakleenMINI R56 thermostat replacement - wipe down the engine with CRC Brakleen and a clean rag.
  10.  Inspect the new thermostat. Make sure the coolant temperature sensor, bleed screw and gasket are installed. Also verify that there is an o-ring on the water supply pipe inlet on the back of the thermostat.MINI R56 thermostat replacement - Make sure the coolant temperature sensor and the bleed screw are installed in the new thermostat. MINI R56 thermostat replacement - Make sure there is a new gasket installed in the new thermostat. Make sure there is an o-ring on the return water pipe inlet.
  11. Install the new thermostat starting with the water supply pipe. The new o-rings fit snug…rock the thermostat back and forth while pushing until the pipe is properly seated on the intake fitting. Lower the metal locking clip and verify it’s in the proper locked position.MINI R56 thermostat replacement - Lower the metal locking clip on the water supply pipe.
  12. Install the three thermostat mounting bolts and torque to 8 Nm (6 ft-lb). We suggest inserting a piece of tape in the socket when installing the rear bolt…it is difficult to get started and can easily drop into the engine and disappear. Use a piece of tape to help secure the rear mounting bolt to the socket to avoid dropping it into the engine. MINI R56 thermostat replacement - Torque the thermostat mounting bolts to 8 Nm (6 ft-lb)
  13. Replace all of the coolant hoses. Make sure the hose clamps are tightened snugly.
  14. Reinstall the rest of the engine following the steps in Section 1 in reverse.

 

Section 3 – Refilling the system with coolant
Now that the MINI R56 thermostat has been replaced, you will need to refill the coolant system and bleed it of any trapped air. The BMW Repair Guide recommends using a coolant vacuum fill tool to properly refill the coolant system in your MINI vehicle. If you do not have a vacuum fill tool, you can use the following manual method of filling and bleeding your system. It is very important that any trapped air in the coolant system is bled out to avoid engine overheating.

  1. Only use Genuine MINI or BMW Antifreeze/Coolant mixed 50/50 with distilled water in your vehicle. Using any other brand of antifreeze/coolant in your MINI is strongly discouraged. Genuine MINI (BMW) Antifreeze/Coolant was specifically engineered for your MINI…other brands may not cool or protect your engine correctly.Only use Genuine MINI or BMW coolant.Only use distilled water to mix with coolant
  2. Turn the ignition on. Do not start the vehicle.
  3. Set the HVAC temperature controls to full warm and the fan speed to its lowest setting (this allows coolant to circulate through the heater core).
  4. Slowly fill the coolant expansion tank until it reaches its maximum level mark. Leave the cap off of the tank.
  5. Start the engine and run at idle for one minute.
  6. After one minute, add more coolant to the expansion tank to bring the level back up to the maximum level mark. Replace the cap on the tank.
  7. With the engine running, use a long flat blade screwdriver to loosen the bleed screw on top of the thermostat (it is located behind the wiring harness on the top of the thermostat). When you see a steady stream of coolant flowing from the bleed screw immediately tighten it. The coolant system is now purged of all air and is properly filled.Use a long screwdriver to reach the bleed screw on top of thermostatBleed screw behind the wiring harness.
  8. Allow the engine to cool and top off the expansion tank if necessary.

 

MINI R56 Thermostat Replacement Finished
If you have any questions or comments, please feel free to contact us. And congratulations for Doing It Yourself!