N20 Cylinder Head Temperature Sensor Repair – BMW 1,2,3,4,5,X,Z Series

0
89

BMW N20 Cylinder Head Temperature Sensor Replacement – 15 Minutes

Basic level repair
Repair cost level 1

The BMW Repair Guide used a 2014 BMW 320i similar to this one for the following article. To see other repairs on our site using this model car, please click on the image below!

2014 BMW 320i Sedan

Repair Summary
The following article gives detailed instructions on replacing the cylinder head temperature sensor in a BMW with the N20 2.0 liter 4 cylinder engine. The N20 engine was used in many BMW models including the 1,2,3,4,5,X and Z vehicles. Even though we have used a 2014 BMW 320i to perform this repair, this article can be applied to any vehicle with the N20 engine with minor modifications.

A BMW N20 cylinder head temperature sensor failure is a known cause of engine power shutdown and the vehicle entering “limp mode”.

There have been reports slowly filtering in from BMW owners of vehicles with the N20 2.0L engine entering “limp mode” while driving for no apparent reason. It usually happens after the engine warms up and while idling at a traffic light or a stop sign. Sometimes a “check engine” light may be displayed…but sometimes it may not.

The 2014 320i that we used for this article started shutting down approximately five minutes into driving with no check engine light and the engine temperature gauge operating correctly. When we turned the engine off and restarted, the vehicle would return to normal operation for a few minutes, only to shut down again. A diagnostic scanner attached to the car revealed a P1290 code, which lead us to believe the cylinder head temperature gauge may be faulty. Replacing the cylinder head temperature gauge immediately cured the issue and the vehicle is back to operating normally.

The BMW N20 cylinder head temperature sensor monitors the engine’s coolant temperature at the top of the engine block. This data is sent to the BMW’s DME (engine control unit) where it is used to manage engine operation and performance. If the sensor reads that the coolant in the cylinder head is too hot the DME will send the engine into “limp mode”, effectively cutting power to the vehicle and avoiding engine overheating.

The issue that is plaguing many BMW owners with the N20 engine is premature failure of the sensor (the 2014 320i that we repaired for this article only had 43,000 miles). BMW N20 cylinder head temperature sensor failure may cause the DME to falsely assume the engine is overheating, forcing the vehicle to cut power and eventually shut down. 

Replacing the BMW N20 cylinder head temperature sensor is a very simple procedure, and depending on the model you are working on can take as little as 15 minutes. It is conveniently located on the front of the engine, and requires a 22mm deep socket to remove and reinstall it.

Affiliate link disclosure – The BMW Repair Guide uses affiliate links in their site. For more information on affiliate links, please click here.

1. Cylinder head temperature sensor (required) – Always purchase a quality sensor from a reputable manufacturer. Cheap generic sensors have a high failure rate. We give you several high quality choices based on your brand preference and budget.

Cylinder head temperature sensor – Febi 13621433076

All BMW vehicles with the N20 engine

Cylinder head temperature sensor – FAE 13621433076

All BMW vehicles with the N20 engine

Cylinder head temperature sensor – BMW 13621433076

All BMW vehicles with the N20 engine
22mm deep socket
Torque wrench- low range
CRC Electronic Cleaner

Section 1 – Removing and installing the cylinder head temperature sensor
Removing and installing the BMW N20 cylinder head temperature sensor in your four cylinder engine is very simple. It is conveniently located on the front of the engine and easily accessible without having to clear any parts out of the way.

  1. Locate and identify the cylinder head temperature sensor. It is on the front of the engine as shown in the images below.bmw n20 cylinder head temperature sensor - The cylinder head temperature sensor is located on the front of the engine bmw n20 cylinder head temperature sensor - The sensor is located on the front of the engine next to the oil cooler bmw n20 cylinder head temperature sensor - You may have to pull a few wires back to uncover the sensor.
  2. Pinch in the metal locking clip on the temperature sensor’s electrical plug. Pull the plug off of the sensor.Pinch in the metal locking clip to release the plug from the sensor. bmw n20 cylinder head temperature sensor - Pull the plug free from the sensor.
  3. Using a 22mm deep socket wrench, remove the BMW N20 cylinder head temperature sensor from the cylinder head.22mm deep socket bmw n20 cylinder head temperature sensor - Remove the old sensor from the cylinder head.Remove the old sensor from the cylinder head
  4. A small amount of engine coolant may drip out of the open hole after the sensor is removed, so have a rag ready.A small amount of coolant may drip out of the open hole when the sensor is removed, so have a rag ready
  5. Install the new sensor into the cylinder and finger tighten. Torque the new BMW N20 cylinder head temperature sensor to 11 Nm (8 ft-lb).bmw n20 cylinder head temperature sensor - Torque the new sensor to 11 Nm (8 ft-lb).
  6. It is always good practice to spray the electrical plug liberally with CRC Electronic Cleaner to remove any dirt, oil or old coolant.bmw n20 cylinder head temperature sensor - Spray the plug with CRC Electronics Cleaner before replacing.
  7. Replace the plug. Make sure it snaps securely into place.

 

BMW N20 Cylinder Head Temperature Sensor Replacement Finished
If you have any questions or comments, please feel free to contact us. And congratulations for Doing It Yourself!