BMW E46 Power Steering Pump Replacement – 1998-2006 3 Series All Models

0
776

BMW E46 Power Steering Pump Replacement – 3 Hours

repair models difficulty bar

The BMW Repair Guide used this 2003 325ci for the following article. To see other repairs on our site using this actual car, please click on the image below!

If your 3 series steering wheel suddenly becomes extremely difficult to turn while the vehicle is running, then you most likely are in need of a BMW E46 power steering pump replacement.

If there was a reader’s poll on which topics we address ad nauseam here at the Repair Guide, our constant reflections on the age of our “beloved” E46s would most certainly win. Yes…they are getting old. Yes…parts are starting to fail. Wait, am I talking about our millennial 3 series bimmers or my recent 35th high school reunion?

The BMW E46 3 series is recognized by automobile enthusiasts as an icon. But like Madonna has recently proven, even icons start to wear out with age and are in need of some corrective surgery. Most E46s still on the road are running with original parts that are beginning to fail.

One part of particular concern is the BMW E46 power steering pump. The accessory belt driven power steering pump is located near the bottom of the engine on the left side of the vehicle. Since the power steering system on a BMW E46 is hydraulic, it requires a pump to create high fluid pressure in the steering rack. The high pressure fluid in the steering rack pushes against a piston when you rotate the steering wheel, making it easy to turn the front wheels.

When the power steering pump fails…you know it immediately. The days of turning your BMW E46 with one hand whilst sipping a non-fat mocha latte with caramel drizzle are over. When a BMW E46 power steering pump fails, you literally have to wrap your arms and legs around the steering wheel to exit the Starbuck’s parking lot.

The good news is that the replacement parts are relatively inexpensive for this “do it yourself” repair. The bad news is you will need to jack the front of your vehicle up to access the pump; if you can get past working under a raised vehicle, you can save a ton of money doing this repair yourself.

Determining what parts you need
In most circumstances, all you will need to do this repair is a new pump. Unless you experienced catastrophic failure of the pump that caused its shaft to seize up, the original pulley and accessory belt can be reused. It is often suggested that a power steering pump replacement creates an opportunity to replace the original BMW plastic pump pulley with an stronger aluminum one. While we do agree with this idea, it is not mandatory. If your plastic pump pulley is in excellent shape with no visible chips or cracks, it is perfectly acceptable to reuse it.

We also suggest replacing your accessory belt if it is showing signs of age or is nearing the end of its service life. Since you will need to pull off the accessory belt to replace the power steering pump, it is a great time to replace it.

Parts, Tools and Supplies

Affiliate link disclosure – The BMW Repair Guide uses affiliate links in their site. For more information on affiliate links, please click here.

Certain parts needed for this repair vary among models and production dates – your vehicle VIN number is needed to verify which part is correct for your vehicle. Not sure which part number to order? The BMW Repair Guide uses realoem.com to verify all of their part numbers. Simply click on the link below, enter the last seven digits of your BMW’s VIN number, and your vehicle model and production date will be displayed along with links to the correct part number for your vehicle.

Get the correct part number for my BMW

Parts
You must have the production date of your BMW E46 3 series to purchase the correct pump. Get the production date for your vehicle from the drivers side door jamb label or by clicking on the link in the above caution box.

  1. Required – choose your power steering pump from one of the following options.
PartQuantityPart #Description
Power Steering Pump – 94965132411094965Production date up to 9/1999 – LF 30
Power Steering Pump – 60036132416760036Production date from 9/1999 – to 9/2001 – LF 20
Power Steering Pump – 56582132416756582Production date from 9/2001- to 9/2002 – LF 30
Power Steering Pump – 60034132416760034Production date from 9/2002 – LF 20

 

2. Required – Power steering fluid.

PartQuantityPart #Description
Power steering fluid – 29576183290429576Pentosin CHF 11S – 1 liter needed

 

3. Optional – purchase an upgraded aluminum pulley.

PartQuantityPart #Description
Power Steering Pulley – 40858132421740858URO brand aluminum pulley

 

4. Optional – purchase a new accessory belt.

PartQuantityPart #Description
Accessory Belt – 06545111281706545Continental 6PK X 1538

 

Tools and Supplies
Floor jack – low profile
Jack stands or Wheel Ramps
10mm socket wrench
13mm socket wrench
Socket extensions
Socket wrench – low profile flex head (optional…but very useful)
Flatblade screwdriver
Trim removal tool kit – plastic
Fan clutch removal tool
Blaster PB Lubricant
T30 torx bit
T50 torx bit
Drain pan – 5 gallon
17mm crows foot socket (preferred) or 17mm open end wrench (optional)
Torque Wrench
Torque wrench- low range
Vise – bench mount
Shears – heavy duty

Procedure
The BMW Repair Guide makes every attempt to publish their repair articles with detailed step by step photographs, videos and written instructions. Since this repair deals with varying years and models, your vehicle may be slightly different than what is shown in the following steps and images. Some repairs may also require additional steps not covered in our articles like: removing covers from the engine and undercarriage, moving wires or hoses to access parts, cleaning and lubricating parts associated with the repair and performing general maintenance.

This is a messy repair! We highly recommend wearing something that you are not afraid to get dirty. This is a messy job, with the chance of oil and/or other automotive fluids getting on both you and the floor beneath your vehicle. Being prepared before starting the repair helps make things go easier!

Section 1 – Accessory belt removal
In order to properly remove and reinstall the accessory belt on the power steering pulley, the vehicle’s cooling fan must be removed. It is very easy to remove and install the accessory belt on a BMW E46 3 series from the top of the engine with the fan removed. Trying to remove and reinstall the accessory belt from the bottom of the engine is extremely difficult and we discourage our readers from attempting to do it this way.

  1. Begin by removing the air box assembly. Use a 10mm nut driver or socket wrench to remove the two air box mounting bolts on the left side of engine compartment.BMW E46 Power Steering Pump Replacement - remove the air box from engine
  2. Disconnect the Mass Air Flow (MAF) sensor.BMW E46 Power Steering Pump Replacement - mass air flow sensor
  3. Using a flat blade screwdriver, loosen the hose clamp connecting the air intake boot to the air box.BMW E46 Power Steering Pump Replacement - Disconnect intake boot
  4. Remove the air box from the engine compartment.BMW E46 Power Steering Pump Replacement - remove air box from vehicle
  5. Next, remove the upper coolant hose from the thermostat by releasing the snap clip with a flat blade screwdriver. Pull the hose off of the thermostat. Release the clips from the hose where it attaches to the coolant reservoir. Remove upper coolant hose from vehicle. BMW E46 Power Steering Pump Replacement - top coolant hose clips BMW E46 Power Steering Pump Replacement - reservoir clips BMW E46 Power Steering Pump Replacement - remove top coolant hose
  6. Use a trim tool to remove the three plastic rivets attaching the air inlet assembly to the front of the vehicle.BMW E46 Power Steering Pump Replacement BMW E46 Power Steering Pump Replacement
  7. Remove the air quality sensor and the wiring harness connection from the right side of the fan shroud.BMW E46 Power Steering Pump Replacement - remove fan shroud electrical connections BMW E46 Power Steering Pump Replacement - remove fan shroud electrical connections
  8. Remove the two fasteners anchoring the fan shroud to the front of the vehicle. These fasteners are often lost or changed over the years, so there may be screws holding the fan shroud…or it may be plastic rivets. We had both.BMW E46 Power Steering Pump Replacement - remove fan shroud screws
  9. Carefully remove the plastic fan shroud, paying attention to the fan blades during removal. It helps to have someone underneath vehicle pressing in on bottom of shroud so it clears the fan blades. Once bottom of shroud is clear of blades, it will pull out smoothly.BMW E46 Power Steering Pump Replacement - remove fan shroud from vehicle
  10. With the fan shroud removed, you can now access the fan clutch nut. Use a BMW fan clutch tool to loosen the fan clutch nut. Remember…the fan clutch nut is a reverse thread! You must turn the nut clockwise (to the right) to loosen it. If you are able to loosen the nut with the tool, remove the fan and proceed to step 12. If you cannot loosen the nut with the tool, go to step 11. BMW E46 Power Steering Pump Replacement - fan clutch nut locationBMW E46 Power Steering Pump Replacement - e46 power steering pump cooling fan removal
  11. It is very common for the fan clutch nut on BMW E46s to seize and not be removable with the fan clutch tool. Lack of maintenance and poor maintenance practices (not greasing nut during prior repairs) causes stripped and seized nuts, making them virtually impossible to remove. Many nuts will show the battle scars of mechanics attempting to remove them…a telltale sign that trouble lingers ahead. Your only option at this point is to remove the fan clutch bolts and remove the plastic cooling fan. Use a T30 torx bit to remove the three fan clutch mounting bolts. Remove the fan from the vehicle.BMW E46 Power Steering Pump Replacement - fan clutch bolt removal BMW E46 Power Steering Pump Replacement - fan clutch bolt removal BMW E46 Power Steering Pump Replacement - fan clutch bolt BMW E46 Power Steering Pump Replacement - remove cooling fan from vehicle
  12. Remove the plastic cover off of the tensioner pulley. The tensioner pulley is located near the middle of the engine above the power steering pump.BMW E46 Power Steering Pump Replacement
  13. Using a T50 torx bit, turn the pulley clockwise until the accessory belt loosens. Reach down and pull the accessory belt off of the tensioner pulley. The belt can now be removed from the power steering pulley.BMW E46 Power Steering Pump Replacement BMW E46 Power Steering Pump Replacement

 

Section 2 – BMW e46 power steering pump removal

  1. Jack and support the front of your vehicle using the four corner wheel stand method as shown in our article BMW Jacking and Supporting for Repairs and Maintenance.
  2. Locate the power steering pump. It is on the left side of the engine below the alternator.BMW E46 Power Steering Pump Replacement - e46 power steering pump location
  3. Remove the cap from the power steering fluid reservoir. This will allow the system to properly drain.bmw e46 power steering pump reservoir
  4. Use a flat blade screwdriver to loosen the hose clamp connecting the suction hose to the pump. Remove the hose from pump allow to drain completely into a 5 gallon drain pan. Be careful…the fluid comes out quickly. Make sure you are not underneath the suction hose when you disconnect it from the pump, or you will get a face full of power steering fluid and a bad case of acne the next morning. ***Option – you can use a fluid removal pump or a “turkey baster” to empty the reservoir first (before removing the suction hose) if you don’t want to get splattered with fluid.remove suction hose from the pump drain the suction hose
  5. Use a 17mm crows foot socket to remove the pressure hose from the pump. Make sure to have a drain pan positioned under the hose to catch the small quantity of fluid still in the pump. You can use a 17mm open end wrench if you wish, but a crows foot is easier due to the confined space. The crows foot will also allow you to torque the nut to spec at the end of the repair.remove pressure hose from the pump drain the pressure hose and the pump
  6. Remove the belt from the power steering pump pulley.remove power steering pulley
  7. There are three bolts anchoring the power steering pump to the engine. There are two mounting bolts that anchor the pump to the front of the engine; one bolt is on the back of the pump and one is on the front. The third bracket bolt anchors the pump to the side of the engine block and is also located at the rear of the pump. The following is an image of our new replacement pump showing the three mounting points for the pump.
    bmw e46 power steering pump - new pump bolt locations
  8. Starting at the rear of the pump, use a 13mm socket wrench with extension to remove the bracket bolt.remove mounting bracket bolt
  9. Use a 13mm socket wrench to remove the rear pump mounting bolt.remove rear mounting bolt
  10. Moving to the front of pump, use the 13mm socket wrench to remove the front pump mounting bolt. A low profile flex head ratchet comes in very handy in this step.remove front mounting bolt
  11. Remove the pump from the vehicle. It is easiest to remove from the rear of the sway bar. Be careful not to tear the tie rod boot when removing (not shown in image). bmw e46 power steering pump removal
  12. Notice the pump we removed is completely destroyed. The pulley shaft has separated from the pump. This could have caused disastrous consequences if left unfixed.photo of old bmw e46 power steering pump - shaft has been destroyed!

 

Section 3 – Pulley removal and installation
When doing a BMW E46 power steering pump replacement, it is recommended that you upgrade from the stock plastic pulley to a newer metal one. This is only a recommendation and not a requirement; if your original plastic pulley is in good shape (free of chips, cracks or scrapes), then reusing it is perfectly acceptable.
Removing and installing the pulley on an E46 power steering pump raises its own set of challenges; since the pulley spins on a shaft, trying to remove the bolts without somehow locking the pulley from spinning can become a lesson in futility. Further compounding the issue is that trying to remove and install the pulley while the pump is still on the vehicle is next to impossible. Don’t trust the photos you see online! You will never be able to torque the pulley bolts properly with the pump installed in the car.
The good news is the pulley bolts are at a relatively low torque (22Nm – 16ft lb) so removing and/or installing them is fairly easy. The trick is to immobilize the pulley without breaking it. This is easily done with an old accessory belt (or an inexpensive new one if you don’t have one lying around) and a table vice. Never attempt to remove or install pulley bolts with an impact wrench. This can cause damage to the pulley…it also may cause excess stress on the pump shaft leading to pump failure.

  1. Cut any “six ribbed” accessory belt you can find in half with a pair of shears. If you are replacing the accessory belt during this repair, use your old one. If you do not have an old belt, run to your local auto parts store and buy a cheap one…they have plenty of them for under 20 bucks.cut an old accessory belt in half
  2. Wrap the accessory belt around the pulley twice and cut off excess. wrap pulley twice with old belt cut off excess
  3. Place the pulley and pump into a table vice. Slowly tighten vice until pulley is secure. DO NOT overtighten. DO NOT allow vice jaws to touch pulley. They should only be pressing in on belt (see image below).secure the pulley in a vice
  4. Remove the three pulley bolts with a 13mm socket wrench.bmw e46 power steering pump - remove the old pulley bolts
  5. Carefully pull the old pump free of pulley. Leave the pulley in the vice.remove old BMW E46 power steering pump from pulley
  6. Install the new pump on the pulley and hand tighten the bolts. Torque bolts to 22Nm (16 ft-lb).torque pulley bolts

 

Installing new BMW E46 power steering pump into vehicle

  1. Install the new pump onto the engine with the two mounting bolts and bracket bolt. Torque all three bolts to 22Nm (16 ft-lb). DO NOT over-torque these bolts or they will strip.
  2. Reinstall the pressure hose and hand tighten the M16 bolt. Torque the bolt with a 17mm crows foot socket to 40Nm (30 ft-lb). This is a lot of torque…proceed carefully. Always double check the torque value on your wrench so you don’t make any mistakes.torque pressure line nut
  3. Reinstall the suction hose and firmly tighten the hose clamp.
  4. Loop the accessory belt back around the power steering pulley. From the top of the engine, reinstall the accessory belt back on the tensioner pulley (section 1, step 13) . Pay particular attention to the belt where it loops around the water pump pulley…this is usually where the belt falls off during installation.
  5. Reinstall the cooling fan. If you were able to remove the fan from the water pump with the fan clutch tool (section 1, step 10), apply a liberal amount of grease (not WD-40…but any thick paste grease) to the fan clutch nut; we do this so the fan can be easily removed in future repairs. Reinstall the fan. Remember…the plastic cooling fan has reverse threads! Turn the nut counterclockwise (left) to tighten.
  6. If you had to remove the plastic cooling fan by removing the fan clutch bolts (section 1 step 11), you will need to reinstall the bolts. First…MAKE SURE PLASTIC FAN is installed in the right direction! If not you will be pulling air out of the engine instead of blowing it in. Reinstalling the bolts is a bit tricky…we advise looking for the threaded blocks on the fan clutch to guide you in. Putting the bolt on the torx bit and extension and then installing is a lot easier than trying to thread them in by hand. Be patient, once you figure out how to do them they go in easy. Use a low torque wrench to tighten the fan clutch bolts to 10Nm (7 ft-lb).clutch hub bolts - use a socket extension for easier installation torque fan clutch bolts
  7. Reinstall the fan shroud, being careful it doesn’t get hung up on the plastic cooling fan. DO NOT force the fan shroud down. If the fan shroud is not installing properly, most likely the plastic tab on the bottom of the shroud is not lining up with with the plastic bracket on the bottom of the radiator (see following images). This step is best done with the aid of a helper who can guide the fan shroud into the bottom radiator bracket while someone pushes from the top.
  8. Reinstall the upper coolant hose by closing the clips and pushing them on to the thermostat and coolant reservoir until you hear them “click”. You may have to put some muscle into them to get them to go on. MAKE SURE YOU HEAR THE METAL hose clips “click” when reinstalling the hose – this means the connections are secure and the clips are seated correctly. The connections to the fluid reservoir can be a pain…so use patience. This is very important…a hose that is improperly installed will leak coolant and quickly become a disaster. Since you have introduced air into the cooling system, you will need to quickly bleed the system. This is a very easy procedure and will be done below in section 4.reinstall coolant hose
  9. Reassemble the rest of the vehicle.

 

Filling, bleeding and testing the BMW E46 power steering pump 

  1. After you have finished reassembling the vehicle, fill the power steering reservoir with an approved power steering fluid.refill power steering reservoir
  2. Start the vehicle. Leave it running through the next steps.
  3. You will need to bleed out any air that is trapped in the coolant lines from removing the top coolant hose. Loosen the bleeder screw on the top of the coolant reservoir to purge any trapped air out of the system. When a steady stream of coolant runs out of the bleeder screw, you can tighten. Be sure to check your coolant level just to make sure you didn’t lose any during the repair. Top off the coolant as necessary (use only a BMW approved coolant – the Repair Guide only uses Genuine BMW Coolant/Anti-freeze 67704 mixed 50/50 with distilled water.bleed the coolant lines
  4. Next you will need to bleed the power steering unit. This is a very simple procedure: With the engine running, sit in the driver seat and turn the steering wheel all the way to the right until it stops. Then, turn the steering wheel all the way to the left until it stops. Repeat this operation two more times. The steering wheel should now turn smoothly with little effort. You have successfully bled the steering system.
  5. Turn the engine off and take one last look under the vehicle to make sure none of the power steering lines are leaking. Check the engine bay and make sure there are no leaks in the upper radiator pipe and everything looks secure.
  6. Check the power steering fluid level and top off if necessary.

BMW E46 Power Steering Pump Replacement Finished
If you have any questions or comments, please feel free to contact us. And congratulations for Doing It Yourself!

The Repair Difficulty Level displays graphically how challenging the repair is, from easy to advanced. Easy repairs usually require very few tools, have short repair times and do not require jacking and supporting the vehicle. As the difficulty level rises, expect the repair to demand more time, specialized tools, and better understanding of mechanics to complete the job.
BMWE46323CiM52 2.5L
BMWE46323iM52 2.5L
BMWE46325CiM54 2.5L
BMWE46325iM54 2.5L
BMWE46325xiM54 2.5L
BMWE46328CiM52 2.8L
BMWE46328iM52 2.8L
BMWE46330CiM54 3.0L
BMWE46330iM54 3.0L
BMWE46330xiM54 3.0L
BMWE46M3S54 3.2L